Any board.
Cut to your list.

Melamine, MDF, veneer and plywood cut, edged, machined and sprayed for furniture makers, interior designers and builders. Collected or delivered nationwide in under five working days.

Upload a cut listOrder free samples

Cut to size

Choose any decor board in the range and send the panel sizes. Our beam saws cut the whole sheet to your list in one pass.

±0.5 mm tolerance2800 × 2070 sheet8 to 38 mm thickness

Edged on PUR

Matching edge tape is bonded on PUR glue machines. The glue line disappears and the joint stays sealed against steam and water.

0.4 to 2 mm ABS edgingZero visible glue line

CNC machined

Hinge bores, grooves, radiused corners, decorative routing and fully shaped panels, straight from your drawing.

35 mm hinge cupsDXF / DWG accepted

Sprayed and on the van

Primer, clear lacquer or any colour, then wrapped, labelled per panel and delivered to site.

Under 5 working daysNationwide delivery
BoardCutEdgeCNCDeliver
Scroll

What we do

Four machines. One cut list.

Send the sizes once. Everything below happens on the same floor, under one job number, so a panel never waits for a courier between processes.

Board cutting

Any decor board cut to your panel sizes on beam saws. Full sheets or single panels, optimised to waste as little board as possible.

±0.5 mmcut tolerance

Panel edgebanding

ABS or matching melamine edge tape applied on PUR glue lines, trimmed and buffed. Two long edges, four edges or any mix per panel.

PURwaterproof bond

CNC cutting

Unusual shapes, routed patterns, hinge drilling, shelf-pin holes and grooves. Send a drawing or describe it and we draw it.

3 axisnesting router

Spray painting

White primer, clear lacquer or colour match on MDF doors, panels and fronts. Book the finish when you place the cut list.

Any RALor NCS colour

The line

Every job travels the floor in this order, under one job number. Scroll to walk it.

1

Beam saw

Full 2800 × 2070 sheets are cut to your panel list on the beam saw. Sizes are optimised against the sheet so you pay for less waste.

±0.5 mmcut tolerance
8–38 mmboard thickness
Anydecor in range
2

Edgebander

ABS or melamine tape applied on PUR glue, trimmed, scraped and buffed. Choose which edges, per panel, on the cut list.

0.4–2 mmedge thickness
PURwaterproof bond
Zerovisible glue line
3

CNC router

Hinge bores, shelf-pin holes, grooves, radius corners, routed patterns and fully shaped panels. Send a DXF or a sketch.

35 mmhinge cups
3 axisnesting router
DXF/DWGaccepted
4

Spray booth

MDF doors, fronts and panels primed, lacquered or colour matched. Book the finish on the same order as the cut.

Any RALor NCS colour
Matt–glosssheen levels
+3–5working days
5

Despatch

Panels wrapped, labelled with your panel names and loaded in install order. Collect from either workshop or we deliver to site.

< 5working days
Nationwidedelivery
8am–4pmcollections

Made to measure, in five working days.

Sliding wardrobe doors, shaker doors and drawer fronts, mirrored signature doors in eight designs, and wall panelling. Ordered to the millimetre and matched to the carcass boards in the same job.

Request a door quote
Sliding doors, walnut and bronze mirror. Scroll to open.

Door styles

Four ways to finish a room.

Each style is cut from the same boards as your carcasses, so colour and grain match across the whole job.

Shaker doorsMDF, primed or sprayed
Sliding doorsbespoke sizes
Signature doorssilver, grey or bronze mirror
Wall panellingslat, fluted, shaker

Decor collections

Every board the trade asks for.

Synchronised woodgrains, stones and textiles, supermatt and high gloss, on chipboard, MDF or plywood cores. Samples are free and go out the same day.

EggerKronospanCleafXyloSaviolaSwiss KronoAlvicSenoplastSerica
Natural oak
Dark walnut
Grey stone
Supermatt white
Anthracite gloss
Linen textile
5working days

Lead times this week

Cut, edged and ready.

  • Cut and edge5 working days or fewer
  • Shaker and sliding doors5 working days
  • Spray finishadd 3 to 5 working days
  • Furniture fittingssame-day collection, next-day delivery

From the trade

“Cut sizes come back exactly as the list, edges clean, no chipping. We stopped checking every panel.”Kitchen fitter, 11 years ordering
“The only supplier that will edge, drill and spray in one order. It saves a week on every wardrobe job.”Interior design studio
“Samples arrived next morning, the boards two days after the client signed off. Nothing else to say.”Joinery workshop